-
1 необходимое напряжение
1) Medicine: required voltage level2) Engineering: desired voltage, needed voltageУниверсальный русско-английский словарь > необходимое напряжение
-
2 ввод с газовой изоляцией
ввод с газовой изоляцией
Ввод, в котором основной изоляцией является газ (отличающийся от окружающего воздуха) под давлением, большим атмосферного или равным ему.
[ ГОСТ 27744-88]EN
gas-insulated bushing
bushing in which the major insulation consists of gas (other than ambient air) at atmospheric pressure or higher
NOTE 1 This definition includes bushings which are intended to form an integral part of gas-insulated equipment, the gas of the equipment being in communication with that of the bushing.
NOTE 2 A bushing which contains solid insulating materials other than the envelope containing the gas (e.g. support for conducting layers or insulating cylinder), is a combined insulation bushing (see 3.13).
NOTE 3 A bushing in which the desired voltage grading is obtained by an arrangement of conducting or semi-conducting layers incorporated in an insulating material (e.g. plastic film) is referred to as a gas insulated condenser graded bushing.
[IEC 60137, ed. 6.0 (2008-07)]FR
traversée à isolation gazeuse
traversée dont l'isolation principale est assurée par un gaz (autre que l'air ambiant) à une pression supérieure ou égale à la pression atmosphérique
NOTE 1 Cette définition comprend les traversées destinées à faire partie intégrante d'une installation à isolation gazeuse où le gaz de l'installation est en communication avec celui de la traversée.
NOTE 2 Une traversée qui comporte des matériaux isolants solides autres que l'enveloppe contenant le gaz (par exemple un support pour des couches conductrices ou un cylindre isolant) est une traversée à isolation composite (voir 3.13).
NOTE 3 Une traversée dans laquelle la répartition de tension souhaitée est obtenue par la disposition de couches conductrices ou semi-conductrices incorporées au matériau isolant (par exemple film plastique) est désignée par une traversée à isolation gazeuse à répartition capacitive.
[IEC 60137, ed. 6.0 (2008-07)]Тематики
EN
FR
Русско-английский словарь нормативно-технической терминологии > ввод с газовой изоляцией
-
3 делитель напряжения
делитель напряжения
-
[IEV number 312-02-32]
делитель напряжения
Преобразующее устройство, состоящее из плеч высокого и низкого напряжения, таких, что напряжение входа прикладывается ко всему устройству, а напряжение выхода снимается с плеча низкого напряжения. [МЭС 301-05-13, измененный]
Примечание
элементами обоих плеч обычно являются резисторы, конденсаторы или их комбинации, а делитель описывается типами и комбинацией используемых элементов (например, резистивный, емкостный или резистивно-емкостный).
[МЭК 60-2]
делитель напряжения
-
[Лугинский Я. Н. и др. Англо-русский словарь по электротехнике и электроэнергетике. 2-е издание - М.: РУССО, 1995 - 616 с.]EN
voltage divider
device comprising resistors, inductors, capacitors, transformer(s) or a combination of these components such that, between two points of the device, a desired fraction of the voltage applied to the device as a whole can be obtained
[IEV number 312-02-32]FR
diviseur de tension
dispositif constitué de résistances, d'inductances, de condensateurs, de transformateur(s) ou d'une combinaison de ces éléments telle que, entre deux points de ce dispositif, on obtient une fraction désirée de la tension appliquée au dispositif entier
[IEV number 312-02-32]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > делитель напряжения
-
4 комплектное распределительное устройство среднего напряжения
комплектное распределительное устройство среднего напряжения
-Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high- voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]
Medium-voltage switchgear (Fig. 4.115) provides for the required control and metering equipment for generators, transformer supply circuits, feeders, large motors, etc., for systems with voltage up to 15,000 V. A large variety of standardized units is available
FIGURE 4.115 Medium-voltage metal-enclosed switchgear. [Westinghouse Electric Corp.][American electricians’ handbook]
Тематики
- комплектное распред. устройство (КРУ)
Синонимы
EN
Русско-английский словарь нормативно-технической терминологии > комплектное распределительное устройство среднего напряжения
-
5 линейный нерегулируемый источник электропитания
линейный нерегулируемый источник электропитания
-
Рис. ABBThe AC mains voltage (50/60 Hz) applied at the input side is transformed to a lower level and rectifi ed by a subsequent rectifi er. Then, a capacitor C smoothes the output voltage of the rectifi er. The dimension of the transformer depends on the desired output voltage.
Due to the design of the electric circuit, the output voltage directly depends on the input voltage which in turn means that variations of the mains voltage have direct effect to the output side. Since no regulation is done on the secondary side, the residual ripple of the output voltage is in the dimension of volts and specifi ed as a percentage of the DC output voltage.
Due to their simple design, unregulated power supplies are very robust and durable. Their effi ciency is approx. 80 %.
Unregulated power supplies are primarily used for simple electromechanical applications that do not require exact output voltages, e.g. for the supply of contactors.
[ABB]Тематики
Синонимы
EN
Русско-английский словарь нормативно-технической терминологии > линейный нерегулируемый источник электропитания
-
6 защита максимального напряжения обратной последовательности (КОД ANSI - 47)
защита максимального напряжения обратной последовательности
Защита по напряжению обратной последовательности для обнаружения обратного направления вращения вращающейся машины
Код ANSI -47
[ Источник]
максимальная защита напряжения обратной последовательности
Защита по напряжению обратной последовательности и обнаружение обратного направления вращения вращающейся машины
Код ANSI -47
[Техническая коллекция Schneider Electric. Выпуск № 1. Защита электрических сетей. Руководство по защитам]EN
47. phase-sequence or phase-balance voltage relay
A relay that functions upon a predetermined value of polyphase voltage in the desired phase sequence, when the polyphase voltages are unbalanced, or when the negative phase-sequence voltage exceeds a given amount.
[ Источник]Тематики
Обобщающие термины
Синонимы
EN
Русско-английский словарь нормативно-технической терминологии > защита максимального напряжения обратной последовательности (КОД ANSI - 47)
-
7 стабилизация
stabilization, hold
- (выдерживание к-л. параметра) — hold
- (демпфирование угловых отклонений) — damping
- антенны — antenna stabilization
- барометрической высоты — (pressure) altitude hold
- боковая (поперечная) — lateral stabilization
-, боковая (автостабилизация канала крена) — roll-axis stability augmentation
-, боковая (выдерживание поперечной устойчивости) — roll-axis stability hold
-, боковая (угла крена) — roll /bank/ (attitude) hold
- воздушной скорости — airspeed hold
- высоты (выдерживание) — altitude hold
-, гироскопическая — gyroscopic stabilization
- крена (выдерживание) — bank (attitude) hold
- крена — bank hold, roll attitude hold
-, креновая (гироагрегата) — roll stabilization
- 'курса (самолета) — heading hold
- курса (при директорном управлении) — heading hold. то hold heading switch mode selector knob on fdi to hdg.
- курса на крм — localizer course hold
- курсовая (выдерживание заданного курса ла) — heading hold(ing)
- курсовая (путевая) — lateral stabilization
(демпфирование угла рыскания автопилотом, демпфером рыскания)
- на курсе — stabilization on course
stabilize on course before passing over the station.
- на осевой линии впп (при заходе на посадку) — runway heading hold
- наклона угла траектории — flight path slope hold
- напряжения — voltage regulation
the voltage regulator provides the regulated voltage.
- оборотов — rpm stabilization
после стабилизации оборотов проверить напряжение и частоту генератора всу. — when rpm has stabilized, check apu generator volts and frequency are normal.
- оборотов двигателя — engine speed /rpm/ stabilization
engine speed stabilizes at... rpm.
- относительно луча (крм или грм) — (loc or gs) beam hold
- пламени (в камере сгорания) — flame stabilization
- по крену (по углу крена) — roll (attitude) hold /stabilization/
- по курсу (выдерживание заданного курса) — heading hold
- полета на заданной высоте — preselected altitude hold
- положения (ла в пространстве) — attitude hold /stabilization/
- по (относительно) осям курca и тангажа — stabilization about yaw and pitch axes
- по тангажу (по углу тангажа) — pitch (attitude) hold /stabilization/
- по угловой скорости крена — roll rate stabilization
- по угловой скорости курса (рыскания) — yaw rate stabilization
- по угловой скорости рыскания — yaw rate stabilization
- по угловой скорости тангажа — pitch rate stabilization
- по углу крена — roll (attitude) hold /stabilization/
- по углу курса — heading hold
- по углу пространственного положения (ла) — attitude hold /stabilization/
- по числу м — mach (number) hold
- по углу тангажа — pitch (attitude) hold /stabilization/
-, продольная (по тангажу) — pitch hold
- пространственного положения (ла) — attitude hold(ing)
-, путевая (курсовая) (автопилотом, демпфером рыскания) — lateral stabilization
- рлс — radar stabilization (rdr stab)
- рыскания — yaw stabilization
- скорости — speed hold
- самолета (в пространстве) — aircraft (attitude) hold
- тангажа — pitch (attitude) hold, pitch stabilization
- температуры — temperature stabilization
when tgt has stabilized in green band.
- (угла) крена — bank (attitude) hold, roll (attitude) hold /stabilization/
- (угла) курса — heading hold
- (угла) тангажа — pitch hold, pitch (attitude) stabilization
pitch hold in heading or vor/loc mode to maintain a desired pitch attitude.
- углового пространственного положения — attitude hold /stabilization/
- числа м — mach holdРусско-английский сборник авиационно-технических терминов > стабилизация
-
8 комплектное устройство первичного распределения электроэнергии
комплектное устройство первичного распределения электроэнергии
-
[Интент]
Рис. ABBПараллельные тексты EN-RU
They are usually installed on the load side of MV/LV transformers or generators.
These assemblies include one or more incoming units, bus ties and a relatively reduced number of outgoing units.
There are also present measuring instruments and other switching and control equipment.
These assemblies have a sturdy structure to withstand the electrodynamic stresses and the weight of big sized apparatus.
As a matter of fact peculiar characteristics of the power center are high rated currents and shortcircuit currents.
The constructional type is a cubicle structure, with metal enclosure and sections divided into compartments with selective access.
[ABB]Такие устройства обычно подключают на стороне нагрузки СВ/НВ трансформаторов или генераторов.
В их состав входят один или несколько блоков ввода, шины и относительно небольшое число блоков вывода.
В состав комплектного устройства первичного распределения электроэнергии входят также измерительные приборы, коммутационные устройства и средства контроля состояния.
Данные комплектные устройства имеют прочную конструкцию, способную выдерживать электродинамическое действие токов и вес крупногабаритной аппаратуры.
Центры распределения электроэнергии характеризуются высокими номинальным током и током короткого замыкания.
С точки зрения конструктивного исполнения они представляют собой многошкафное комплектное устройство в металлической оболочке, состоящее из секций, каждая из которых разделена на отсеки с независимым доступом.
[Перевод Интент]Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
- комплектное распред. устройство (КРУ)
EN
Русско-английский словарь нормативно-технической терминологии > комплектное устройство первичного распределения электроэнергии
-
9 НКУ защищенное
- safety enclosed switchgear
- safety enclosed board
- enclosed switchboard
- enclosed assembly (of switchgear and controlgear)
НКУ защищенное
НКУ закрытое со всех сторон (за возможным исключением монтажной поверхности), в котором после его установки обеспечивается степень защиты не менее IP2X.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
защищенное НКУ
НКУ, конструкция которого обеспечивает требуемую степень защиты со всех сторон от прикосновения к частям, находящимся под напряжением (за исключением монтажной поверхности).
[ ГОСТ Р МЭК 61439.1-2013]EN
enclosed assembly (of switchgear and controlgear)
an assembly enclosed on all sides, top and bottom in such a manner as to provide a specified degree of protection
NOTE – The mounting surface may form a part of the enclosure when specified in the relevant publication.
[IEV number 441-12-02]FR
ensemble (d'appareillage de connexion et de commande)
sous enveloppe
ensemble comportant une paroi sur toutes ses faces latérales, supérieure et inférieure, de façon à assurer un degré de protection spécifié
NOTE – La surface de montage peut faire partie de l'enveloppe lorsqu'une publication particulière le spécifie.
[IEV number 441-12-0
Шкаф - защищенное НКУ, предназначенное для установки на полу
Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Обобщающие термины
Синонимы
EN
- enclosed assembly (of switchgear and controlgear)
- enclosed switchboard
- safety enclosed board
- safety enclosed switchgear
DE
FR
Русско-английский словарь нормативно-технической терминологии > НКУ защищенное
-
10 желательно
•It is desirable to use the maximum possible voltage.
* * *Желательно -- it is desired to (+ inf.), it is desirable to (+ inf.), it is desired that (+ subjunctive 1), it is desirable that (+ subjunctive 1)Русско-английский научно-технический словарь переводчика > желательно
-
11 категория перенапряжения (в цепи или электрической системе)
- surge voltage category
- overvoltage withstand categories
- overvoltage category (of a circuit or within an electrical system)
- overvoltage categories
категория перенапряжения (в цепи или электрической системе)
Условное число, основанное на ограничении (или регулировании) значений ожидаемого переходного перенапряжения, возникающего в цепи (или в электрической системе с различными номинальными напряжениями), зависящее от способов воздействия на перенапряжения.
Примечание. В электрической системе переход от одной категории перенапряжения к другой, более низкой, достигается средствами, совместимыми с требованиями к переходным участкам, например с помощью устройства для защиты от перенапряжений или последовательно-параллельного присоединения импеданса, способного рассеять, поглотить или отклонить энергию соответствующего импульсного тока с целью снижения переходного перенапряжения до желательно меньшей категории перенапряжения.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
категория перенапряжения
Категория электротехнического оборудования по стойкости изоляции к импульсным перенапряжениям (всего четыре категории: I, II, III, IV)
[Интент]EN
overvoltage category (of a circuit or within an electrical system)
conventional number based on limiting (or controlling) the values of prospective transient overvoltages occurring in a circuit (or within an electrical system having different nominal voltages) and depending upon the means employed to influence the overvoltages
NOTE In an electrical system, the transition from one overvoltage category to another of lower category is obtained through appropriate means complying with interface requirements, such as an overvoltage protective device or a series-shunt impedance arrangement capable of dissipating, absorbing, or diverting the energy in the associated surge current, to lower the transient overvoltage value to that of the desired lower overvoltage category
[IEC 60947-1, ed. 5.0 (2007-06)]FR
catégorie de surtension (d'un circuit ou dans un réseau)
nombre conventionnel, basé sur la limitation (ou la commande) des valeurs des surtensions transitoires présumées apparaissant dans un circuit (ou dans un réseau où existent des sections de tensions nominales différentes) et dépendant des moyens employés pour agir sur ces surtensions
NOTE Dans un réseau, le passage d'une catégorie de surtension à une autre de catégorie inférieure est réalisé à l'aide de moyens appropriés répondant aux prescriptions d'interface, tels qu'un dispositif de protection contre les surtensions ou des impédances disposées en séries et/ou en parallèle capables de dissiper, d'absorber ou de détourner l'énergie du courant de surcharge correspondant, afin d'abaisser la valeur des surtensions transitoires à celle qui correspond à la catégorie de surtension inférieure recherchée
[IEC 60947-1, ed. 5.0 (2007-06)]Требуемая стойкость к импульсным напряжениям, кВ:
-
Оборудования на вводе в установку ( IV категория перенапряжения)
-
Оборудования распределительных и конечных цепей ( III категория перенапряжения)
-
Электробытовых приборов и электроприемников ( II категория перенапряжения)
-
Специально защищенного оборудования ( I категория перенапряжения)
[ ГОСТ Р 50571-4-44-2011( МЭК 60364-4-44: 2007) ]
Тематики
- электротехника, основные понятия
EN
- overvoltage categories
- overvoltage category (of a circuit or within an electrical system)
- overvoltage withstand categories
- surge voltage category
FR
Русско-английский словарь нормативно-технической терминологии > категория перенапряжения (в цепи или электрической системе)
-
12 приводить к
•This method offers savings in production time.
•Removal of the denaturing conditions brings about the formation of...
•This research has culminated in the discovery of...
•The use of a driving belt could give rise to vibrations.
•If solute concentration varies over many atomic distances, a variation in lattice parameter will result.
•Flapping of the belt could result in poor finish.
•The current in the motor increases, and the result is overheating.
•Uneven removal of excess metal tends to redistribute stresses.
•In areas where present climates are not conducive to the deposition of...
II•The mixture is adjusted to pH 6.8.
•Biotin deficiency in animals is associated with dermatitis, loss of hair,...
•Thermal stresses sometimes produce surface cracking.
•A small error in ψ will eventually produce a significant error in the fields.
•The change in contact resistance effects the desired current change.
•These collisions can involve either a gain or loss in mechanical energy.
•Continued condensation causes the period of rotation to shorten.
Русско-английский научно-технический словарь переводчика > приводить к
-
13 соответствующий
•Examine the corresponding values of...
•These effects must he limited to a magnitude compatible with the desired accuracy.
•The extinct bird had massive legs, in keeping with great body weight.
•Test equipment appropriate to each test is installed.
•To maintain the requisite temperature,...
•Steel conforming to (or complying with) the specifications...
II•We supplied the hydraulic equipment and associated control systems.
•Noise in electrical circuits arises because all the mechanisms involved are in dynamic and not absolute equilibrium.
•Television transmitters and their associated transmission lines...
•The liver, spleen, kidneys... with ( their) associated nerves and blood vessels, are located in...
•Specialists trained in the pertinent (or relevant) branches of engineering...
•A cold storage plant is a large insulated building, with its attendant refrigeration equipment.
•Selection of the proper aluminium alloy is extremely important.
••This variation can be measured by suitable photometers.
•Appropriate substitutions should be made.
•These numbers may be written with the appropriate algebraic signs.
IV•This will be discussed in the relevant (or corresponding, or appropriate) sections of the book.
•Pertinent information is available in...
•The ions move to their respective electrodes under the influence of the applied voltage.
•and P2 are the periods of revolution of planet-1 and planet-2, D1 and D2 are their respective distances.
Русско-английский научно-технический словарь переводчика > соответствующий
-
14 необходимое высокое выходное напряжение
Engineering: desired high voltage outputУниверсальный русско-английский словарь > необходимое высокое выходное напряжение
-
15 настройка
alignment, adjustment, ( программы для работы на конкретной ЭВМ) customization, lineup связь, lining-up, tune радио, tuning, tuning control, set, setting, setting-up, setup, trim* * *настро́йка ж.1) adjustment2) элк. ( одиночного параметра или элемента) adjustment; ( обеспечение взаимодействия цепей или элементов) alignmentнастро́йка автомати́ческого регуля́тора1. ( процесс) adjustment, tuning2. ( положение) controller settingпроизводи́ть настро́йку автомати́ческого регуля́тора — adjust the controller settingнастро́йка валко́в прок. — roll adjustmentнастро́йка кали́бров прок. — pass set-upнастро́йка на частоту́ — tuningкорректи́ровать [осуществля́ть] настро́йку (на частоту́) по дискримина́тору — derive tuning-error signal [information] from the discriminator, use discriminator voltage as the tuning-error signal [information]проходи́ть [«проскочи́ть»] настро́йку (на частоту́) — scan past the (desired) tuningсполза́ть с (частоты́) настро́йки — drift out of tuneуточня́ть настро́йку (на частоту́) — refine the tuningнастро́йка на частоту́, бесшу́мная — quiet [silent] tuningнастро́йка на частоту́, визуа́льная — visual tuningнастро́йка на частоту́, гру́бая — coarse tuningнастро́йка на частоту́, кно́почная — push-button tuningнастро́йка на частоту́, механи́ческая — mechanical tuningнастро́йка на частоту́ одно́й ру́чкой — unicontrol station [single-dial, gang, single-knob] tuningнастро́йка на частоту́, о́страя — sharp tuningнастро́йка на частоту́ с растя́жкой диапазо́на — band-spread tuningнастро́йка на частоту́, тупа́я — broad tuningпредвари́тельная настро́йка — initial tune-upнастро́йка реле́, нейтра́льная — unbiased [centred] adjustment of a relayнастро́йка реле́ с преоблада́нием — biased adjustment of a relayнастро́йка ста́на — set-up of a millнастро́йка то́чки регули́рования1. ( процесс) control point adjustment2. ( состояние) control-point setting* * * -
16 сервомеханизм
servomechanism, servo mecha-
nism, servo
механизм, в котором выходная величина (напр., угловое перемещение, обороты, напряжение) контролируется и сравнивается с заданной величиной, a разность между этими величинами (сигнал рассогласования) используется для срабатывания к-п. системы. — а mechanism in which the output quantity, such as angular position, rotational speed, voltage, etc., is monitored and compared with a desired quantity, the difference between the two quantities (the error) being used to actuate the system and to generate a rate of change of the output.
- блокировки включения реворса — thrust reverser lock-out servo
- дозирующей иглы (регулятоpa топлива) — throttle valve servo mechanismРусско-английский сборник авиационно-технических терминов > сервомеханизм
-
17 смещение
displacement, deviation, shift
- блока на амортизаторах — unit sway on shockmounts /shock insulators/
-, боковое (рис. 124) — offset distance
enter offset distance on the keyboard.
-, боковое, заданное — selected offset distance
-, боковое (ла в горизонтальной плоскости относительно равносигнальной зоны крм) — lateral displacement
-, боковое (линейное) — offset distance
расстояние между линиями номинального (заданного) и смещенного курса (параллельной линии пути) (рис. 124).
-, боковое (вправо) фактическое — actual offset distance (to right)
-, боковое (от заданной траектории в горизонтальной плоскости) — lateral displacement (from desired or selected path)
-, вибрационное (в одну cторону от средней точки. см. вибросмещение) — excursion single movement from mean point in oscillating motion.
- оси лопасти (возд. винта) — blade sweep
angular deviation of locus of centroids of blade sections from radial line.
- оси лопасти (возд. винта) к задней кромке — (blade) trailing sweep. а deviation toward the trailing edge.
- оси лопасти (возд. винта) к передней кромке — (blade) leading sweep. а deviation towards the leading edge.
- полюса земли — earth's pole migration
- стрелки (прибора) — pointer displacement
-, угловое — angular displacement
крен самолета определяется no угловому смещению самолетика относительно индекса горизонта (аг). — roll information is an angular displacement between the miniature aircraft and artificial horizon (bar).
- фазы — phase shift
the phase of voltage is shifted 90 deg.
- центровки — center of gravity (cg) shift
- центровки за счет снаряжения — center of gravity shift caused by operational items
- центровки, поперечное — lateral center-of-gravity shift
- центровки, продольное — longitudinal center-of-gravity shift
- щетки (потенциометра) — wiper displacementРусско-английский сборник авиационно-технических терминов > смещение
-
18 цепь (электрическая)
circuit (cct)
ряд соединенных проводников для прохождения эл. тока. — а number of conductors connected together for the purpose of carrying an electrical current.
соединение нескольких устроиств, образующее один или несколько каналов (контуров) для выполнения определенных электрических или радиоэлектронных функций. — the interconnection of a number of devices in oле or more closed paths to perform а desired electrical or electronic function.
- блокировки (эл.) — interlocking circuit
цепь, в которой работа одного элемента эл. оборудования зависит от окончания срабатываний других элементов. — а circuit in which the орегation of one item of electric apparatus is made dependent on the fulfilment of certain predetermined conditions on other items.
- блокировки — lock-out /locking-out/ circuit
цепь, служащая для отключения и удержания в нерабочем состоянии устройства при нарушении его нормальной работы. — function is to shut down and hold а device out of service on occurence of abnormal conditions.
- взрыва (сро) — (trsp) destruct circuit
- включена (готова к работе) — circuit armed
- возбуждения (генератора, эл. мотора) — field circuit
- галля (роликовая) — roller chain
-, гальванически развязанная — decoupling circuit
а circuit used to prevent interaction of one circuit with anotheг.
- задержки (времени) — delay circuit
цепь, обеспечивающая задержку прохождения эл. сигнала no времени, — а circuit which delays the passage of а pulse or signal from one part of a circuit t another.
- зажигания — ignition circuit
-, замкнутая — closed circuit
эл. цепь, обеспечивающая протекание эл. тока при подаче напряжения (наличии разности потенциалов), — а complete electric circuit through which current may flow when а voltage is арplied.
-, кольцевая — loop circuit
энергопитание обеспечивается по раздельным многоканальным или кольцевым цепям. — electrical energy supply is ensured by means of multichannel or loop circuits separately routed.
-, коммутационная — switching circuit
-, контрольная — monitoring /monitor/ circuit
цепь прибора (или системы). контролирующая нормальную работу прибора, и вызывающая срабатывание устройств сигнализации отказа прибора или прекращения подачи питания. — monitor circuits defect a fault in a system.
- контроля, электронная — electronic monitoring circuit
электронная цепь контроля работы пилотажного командного прибора вызывает срабатывание (появление) блейкора красного цвета в случае неисправности (неправильногo показания) прибора. — the electronic monitoring circuits within the flight director deflect red warning flaps into view if a failure occurs that will cause incorreet display.
-, многоканальная — multi-channel circuit
- нагрузки — load circuit
цепь от источника питания до нагрузки (напр., эпектронная лампа эл. двигателя) — the complete circuit required to transfer power from а source to а load (e.g., electron tube, electric motor).
-, нарушенная (эл.) — open/ broken/ circuit
-, незамкнутая — open circuit
разомкнутая цепь, не обеспечивающая протекание эл. тока, — а circuit which does not provide а complete path for the flow of current.
- обратной связи — feedback circuit
- опроса (эвм) — sampling circuit
-, параллельная — parallel circuit
цепь, в которой все положительные и отрицательные вводы и выводы соединены в соответствующих общих точках, — а circuit in which all positive terminals and negative terminals are connected to their corresponding common points.
- питания — feed/ power supply/ circuit
-, последовательная — series circuit
цепь,в которой вывод одногo сопротивления (нагрузки) соединен с вводом следующего, и т.д. — а circuit in which resistance or other components are connected end to end.
- потребителя (эл.) — load circuit
- прохождения сигнала — signal flow circuit
-, разомкнутая (разорванная) — open/ broken/ circuit
-, роликовая — roller chain
- самоконтроля — self-test circuit
- связи (между системами, блоками) — coupling circuit
- соединения на — ground circuit
- управления — control circuit
-, швартовочная (груза в кабине) — (cargo) tie-down /anchoring chain
-, электрическая — electric circuit
-, электронная — electronic circuit
обрыв ц. — broken circuit
включать в ц. — connect in circuit
сопротивление, включенное в цепь, — а resistor is connected in circuit.
закреплять на ц. — chain
крышка закреплена цепочкой к горловине, — the cap is chained to the filler.
замыкать ц. — complete/ close/ circuit
реле замыкает цепь. защищать ц. с помощью аэс — the relay completes the circuits. protect circuit by circuit breaker
размыкать (разрывать) ц. — break/ open/ circuitРусско-английский сборник авиационно-технических терминов > цепь (электрическая)
-
19 контроль синхронизма (КОД ANSI - 25)
контроль синхронизма
Контроль синхронизма/контроль напряжения (разрешенного соединения двух частей электрической сети)
Код ANSI -25
[ Источник]
контроль синхронизма
контроль синхронизма до полачи команды на включение двух частей сети
[Техническая коллекция Schneider Electric. Выпуск № 1. Защита электрических сетей. Руководство по защитам]EN
25. synchronizing or synchronism-check device
A device that operates when two ac circuits are within the desired limits of frequency, phase angle, and voltage to permit or cause the paralleling of these two circuits.
[ Источник]Тематики
Обобщающие термины
EN
Русско-английский словарь нормативно-технической терминологии > контроль синхронизма (КОД ANSI - 25)
См. также в других словарях:
Voltage Identification Digital — or VID is a circuit concept developed to provide the central processing unit (CPU) of a computer with the appropriate supply voltage. Instead of having a power supply unit generate some fixed voltage, the CPU uses a small set of digital signals,… … Wikipedia
Voltage regulator — A popular three pin 12 V DC voltage regulator IC. A voltage regulator is an electrical regulator designed to automatically maintain a constant voltage level. A voltage regulator may be a simple feed forward design or may include negative feedback … Wikipedia
voltage divider — n. a device consisting of a resistor or series of resistors connected across a source of voltage and having one or more fixed or adjustable intermediate contacts: from any two terminals a desired reduced voltage may be obtained … English World dictionary
Voltage-to-current converter — Introduction For a variety of reasons, in low voltage electronics, voltage is a more frequently used data carrier. Thus electronic devices tend to be labeled with voltage inputs and outputs. However some devices are labeled in terms of current… … Wikipedia
Voltage regulator tube — A voltage regulator tube (VR tube) is an electronic component used as a shunt regulator to hold a voltage constant at a pre determined level.Physically, these devices resemble vacuum tubes, but there are two main differences: * Their glass… … Wikipedia
voltage divider — noun resistors connected in series across a voltage source; used to obtain a desired fraction of the voltage • Syn: ↑potential divider • Hypernyms: ↑resistor, ↑resistance • Hyponyms: ↑potentiometer, ↑pot … Useful english dictionary
Constant voltage speaker system — Constant voltage speaker systems refer to networks of loudspeakers which are connected to an audio amplifier using step up and step down transformers to simplify impedance calculations and to minimize power loss over the speaker cables. They are… … Wikipedia
Delta-sigma modulation — Delta sigma (ΔΣ; or sigma delta, ΣΔ) modulation is a method for encoding high resolution or analog signals into lower resolution digital signals. The conversion is done using error feedback, where the difference between the two signals is… … Wikipedia
electric motor — motor (def. 4). [1885 90] * * * Introduction any of a class of devices that convert electrical energy to mechanical energy, usually by employing electromagnetic phenomena. Most electric motors develop their mechanical torque by the… … Universalium
Inverter (electrical) — An inverter is an electrical device that converts direct current (DC) to alternating current (AC)[1]; the converted AC can be at any required voltage and frequency with the use of appropriate transformers, switching, and control circuits. Solid… … Wikipedia
Pulse-width modulation — (PWM) of a signal or power source involves the modulation of its duty cycle, to either convey information over a communications channel or control the amount of power sent to a load. PrinciplePulse width modulation uses a square wave whose pulse… … Wikipedia